توضیحات
TPS5120 يک کنترلر باک سنکرون دو کاناله و با راندمان بالا است که در آن خروجي ها 180 درجه خارج از فاز هستند که باعث کاهش ريپل جريان ورودي مي شود و در نتيجه هزينه خازن ورودي را کاهش مي دهد. پين PWM/SKIP به حالت کار اجازه مي دهد تا در شرايط بار سبک از حالت PWM به حالت پرش تغيير کند. حالت پرش فرکانس عملياتي کمتري را فعال ميکند و عرض پالس را به ماسفت سمت پايين کوتاه ميکند و بازده را در شرايط بار سبک افزايش ميدهد. اين دو حالت، همراه با درايورهاي يکسو کننده سنکرون، زمان مرده، و جريان خاموش بسيار کم، اجازه مي دهد تا در برق صرفه جويي شود و عمر باتري در تمام شرايط بار افزايش يابد. درايورهاي 1.5 A (معمولي) MOSFET سمت بالا و پايين روي تراشه براي هدايت ماسفت هاي N-channel ارزان تر طراحي شده اند. حفاظت جريان بدون مقاومت و ولتاژ ثابت درايور سمت بالا، طراحي منبع تغذيه را ساده کرده و تعداد قطعات خارجي را کاهش مي دهد. هر کانال مستقل است و يک کنترلر مجزا، حفاظت جريان اضافه و کنترل آماده به کار ارائه مي دهد. توالي يابي انعطاف پذير است و مي توان آن را با انتخاب مقادير مختلف خازن شروع نرم تنظيم کرد. ساير ويژگيها مانند قفل کم ولتاژ، برق خوب، اضافه ولتاژ، کمبود ولتاژ و حفاظت در برابر اتصال کوتاه قابل برنامهريزي، قابليت اطمينان سيستم را افزايش ميدهند.
Description
The TPS5120 is a dual channel, high-efficiency synchronous buck controller where the outputs run 180 degrees out of phase, which lowers the input current ripple, thereby reducing the input capacitance cost. The PWM/SKIP pin allows the operating mode to switch from PWM mode to skip mode under light load conditions. The skip mode enables a lower operating frequency and shortens the pulse width to the low-side MOSFET, increasing the efficiency under light load conditions. These two modes, along with synchronous-rectifier drivers, dead time, and very low quiescent current, allow power to be conserved and the battery life to be extended under all load conditions. The 1.5 A (typical) high-side and low-side MOSFET drivers on-chip are designed to drive less expensive N-channel MOSFETs. The resistorless current protection and fixed high-side driver voltage simplify the power supply design and reduce the external parts count. Each channel is independent, offering a separate controller, overcurrent protection, and standby control. Sequencing is flexible and can be tailored by choosing different softstart capacitor values. Other features, such as undervoltage lockout, power good, overvoltage, undervoltage, and programmable short-circuit protection promote system reliability
|